Store address and hours
location_on 4131 Fraser St. Vancouver BC Get Directions
phone 604-875-1993 Call us
access_time Hours
Monday - Friday | 9AM - 5:30PM |
Saturday - Sunday & Holidays | Closed | See Holiday Hours |
-
close
-
CATEGORIES
-
-
-
-
-
-
-
-
-
-
-
-
-
Featured Items
-
-
-
-
-
-
-
More mirco-controllers
-
More Developement Tools
-
-
More Prototyping
-
More Modules
-
-
Featured Items
-
More prototyping Tools
-
-
-
-
-
-
-
-
Featured Item
-
-
-
-
-
-
-
Featured Items
-
-
-
-
-
-
-
-
Featured Items
-
-
-
-
-
-
-
-
-
-
-
-
-
Featured Items
-
-
-
-
-
-
-
-
-
Featured Items
-
-
-
-
-
-
Popular Cleaners
-
-
-
Featured Items
-
-
-
-
-
-
-
Featured Items
-
-
-
-
-
Featured Items
-
-
-
-
Featured Products
-
-
-
-
-
more motor
-
-
more power supplies
-
-
Featured Items
-
-
-
more electrical devices
-
-
-
-
-
-
-
Featured Items
-
-
-
-
-
-
BRANDS
-
- PROJECTS
-
COMMUNITY
-
-
-
FEATURED POSTS
-
-
-
- SALE
TAMIYA 70110 4-SPEED CRACK-AXLE GEARBOX KIT
Description
The 70110 Tamiya 4-Speed Crank Axle Gearbox is small but has a lot of power.
The Tamiya 4-speed crank-axle gearbox has four possible gear ratios, including the highest gear ratio of Tamiya’s gearbox series, 5402:1, as well as 126:1, 441:1, and 1543:1. This gearbox also features a worm gear, which locks the output shaft when the motor is not turning. A clutch gear prevents the gearbox from destroying itself in case the output shaft gets stuck. The kit comes with all parts necessary to build the gearbox in any of the four possible configurations.
Color options
- 70110 4-speed crank-axle gearbox — This gearbox is solid gray and comes packaged in a box.
Complementary products
The output shafts included in this kit are 3 mm hexagonal axles that are 10 cm (about four inches) from tip to tip. The axles work with any of the Tamiya wheels we carry, giving you many options for your robot speed. The low-voltage motors run on 3-6 volts and draw up to a few amps, making them perfect candidates for the Pololu low-voltage dual serial motor controller and the DRV8833 motor driver carrier (2130-POLOLU). Motor overheating can be caused by excessive stalling, even at very low voltages. We recommend that you use stall-detection sensors, or just watch your robot, to make sure that it doesn’t stall for more than a few seconds at a time.
Note that you can replace the motor in this kit with a lower-current, higher-voltage motor (1117-POLOLU) if you want to use this gearbox with controllers such as the qik 2s9v1 dual serial motor controller (1110-POLOLU), TB6612FNG dual motor driver carrier, or Baby Orangutan B-328 robot controller.
Note: The 4-speed crank-axle gearbox is a kit; assembly is required. To use the kit in robotics projects, you need to connect the motors to your own robot controller.
General specifications
Typical operating voltage: | 3 V |
---|---|
Gear ratio options: | 126, 441, 1543, 5402 :1 |
Free-run motor shaft speed @ 3V: | 12300 rpm |
Free-run current @ 3V: | 150 mA |
Stall current @ 3V: | 2100 mA |
Motor shaft stall torque @ 3V: | 0.5 oz·in |
Color: | gray |
Notes:
- 1- A theoretical speed of the gearbox output shaft can be computed by dividing this speed by the gear ratio.
- 2- This is the no-load current of the motor when disconnected from the gears in the gearbox; the no-load current of the entire gearbox with the motor connected will be slightly higher and will vary depending on the gear ratio.
- 3- A theoretical torque of the gearbox output shaft can be computed by multiplying this torque by the gear ratio.