ARDUINO MKR WIFI 1010

All pictures are for illustrative purposes only.

PID# 109975

CA$60.00 EACH
Out of Stock
Quantity

Request a large quantity quote

Description

The MKR WiFi 1010 is a great choice for any beginner, maker or professional to get started with Internet of Things (IoT). Using the popular Arm® Cortex®-M0 32-bit SAMD21 processor, it also features the and the ECC508 crypto-chip for security. The board is part of the MKR family, where you can choose from a large variety of shields to build projects out of the box with minimal effort!

WiFi and Bluetooth
u-blox NINA-W102

Enables Bluetooth® and Wi-Fi connectivity for the MKR WiFi 1010 board.

Core
Cortex-M0 32-bit SAMD21

The powerful, low-power processor that is used in all MKR Family boards.

Crypto Chip
ATECC508 crypto chip

The ECC508 crypto chip makes sure your data remains secure and private, and can store up to 16 keys in an EEPROM array.

Please read: operating voltage is 3.3V

The microcontroller on the this board runs at 3.3V, which means that you must never apply more than 3.3V to its Digital and Analog pins. Care must be taken when connecting sensors and actuators to assure that this limit of 3.3V is never exceeded. Connecting higher voltage signals, like the 5V commonly used with the other Arduino boards, will damage the board.

Please read: black conductive foam

You should remove the black conductive foam from the board pins before usage. If you don't remove it, the board may behave erratically.

Tech specs

The Arduino MKR WiFi 1010 is based on the SAMD21 microcontroller.

MICROCONTROLLER SAMD21 Cortex®-M0+ 32bit low power ARM® MCU (datasheet)
RADIO MODULE u-blox NINA-W102 (datasheet)
BOARD POWER SUPPLY (USB/VIN) 5V
SECURE ELEMENT ATECC508 (datasheet)
SUPPORTED BATTERY Li-Po Single Cell, 3.7V, 1024mAh Minimum
CIRCUIT OPERATING VOLTAGE 3.3V
DIGITAL I/O PINS 8
PWM PINS 13 (0 .. 8, 10, 12, 18 / A3, 19 / A4)
UART 1
SPI 1
I2C 1
ANALOG INPUT PINS 7 (ADC 8/10/12 bit)
ANALOG OUTPUT PINS 1 (DAC 10 bit)
EXTERNAL INTERRUPTS 10 (0, 1, 4, 5, 6, 7, 8,9, 16 / A1, 17 / A2)
DC CURRENT PER I/O PIN 7 mA
CPU FLASH MEMORY 256 KB (internal)
SRAM 32 KB
EEPROM no
CLOCK SPEED 32.768 kHz (RTC), 48 MHz
LED_BUILTIN 6
USB Full-Speed USB Device and embedded Host
LENGTH 61.5 mm
WIDTH 25 mm
WEIGHT 32 gr.

Conformities

The following Declarations of Conformities have ben granted for this board:
ISED/IC
MIC
WEE
RCM
RoHS
CE
FCC
UKCA
REACH
For any further information about our certifications please visit docs.arduino.cc/certifications

Documentation

OSH: Schematics

The MKR WiFi 1010 is open-source hardware! You can build your own board using the following files:

EAGLE FILES IN .ZIP SCHEMATICS IN .PDFFRITZING IN .FZPZ

FAQs

Batteries, Pins and board LEDs

  • Battery capacity: rechargeable Li-Ion, or Li-Po. Please make sure the battery connector suits your battery.
  • Battery connector: The connector is of type JST S2B-PH-SM4-TB(LF)(SN). Mating connector is JST PHR-2.
  • Vin: This pin can be used to power the board with a regulated 5V source. If the power is fed through this pin, the USB power source is disconnected. This is the only way you can supply 5v (range is 5V to maximum 6V) to the board not using USB. This pin is an INPUT.
  • 5V: This pin outputs 5V from the board when powered from the USB connector or from the VIN pin of the board. It is unregulated and the voltage is taken directly from the inputs.
  • VCC: This pin outputs 3.3V through the on-board voltage regulator. This voltage is 3.3V if USB or VIN is used and equal to the series of the two batteries when they are used
  • LED ON: This LED is connected to the 5V input from either USB or VIN. It is not connected to the battery power, thus minimizing the impact on battery usage. It is therefore normal to have the board properly running on battery power without the LED ON being lit.
  • Onboard LED: On MKR WAN 1010 the onboard LED is connected to D6.