Product ID: 15259
4-CHANNEL I2C-SAFE BI-DIRECT LOG. LEVEL CONVERTOR. Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V.
Product ID: 16042
GND VCC, which can be either 3.3V or 5V (a 3.3V stabilizer is included) OUT, which should be connected directly to an arduino analog input pin The module is based on the MAX9812 chip from Maxim Integrated. It’s a low-cost fixed gain (20dB) microphone amplifier IC.
Product ID: 15307
This is a electronic microscope designed for PC solution with friendly user interface, which can be used to snap HD pictures and capture the video, and also to measure the objects. This USB digital microscope can magnify objects up to 400 times their original size and uses a dynamic image sensor and eight super bright white LED lights for creating...
Product ID: 447
Here, for all your mechatronic needs, is a simple, high quality continuous full-rotation servo motor. This servo is able to take in 6 volts and deliver 66.7 oz-in. of maximum torque at 70 r/min. A standard 3-pin power and control cable is attached and all hardware listed below is included.
Product ID: 4471
Rotation: 360° Gear: plastic Servo type: analog Voltage: 4.8 to 6V Torque: 3 to 3.5 kg.cm Speed: 0.14 to 0.12 seconds/60° Sizes: 40.8 x 20.1 x 38mm Weight: 36g Cable length: 180mm Motor type: iron core Gears: POM gears, nylon gears
Product ID: 487
Specifications Modulation: Analog Torque: 4.8V: 25.00 oz-in (1.80 kg-cm) Speed: 4.8V: 0.12 sec/60° Weight: 0.32 oz (9.0 g) Dimensions: Length:0.91 in (23.0 mm)Width:0.48 in (12.2 mm)Height:1.14 in (29.0 mm) Motor Type: 3-pole Gear Type: Plastic Rotation/Support: Bushing
Product ID: 15272
RAMPS 1.4 3D PRINTER STEPPER DRIVER SHIELD FOR MEG
Product ID: 4862
Quick drying, tough, durable acrylic base pigmented with high purity silver. Excellent for repairing and modifying printed circuits. Silver content provides superior corrosion resistance. The microtip dispensing pen is ideal for precision application. Also available in a liquid container. Catalog NumberSizeDescription 8420-P 0.3 oz Pen
Product ID: 4810
MG Chemicals cold spray is 100% HFC 134A non-flammable gas. It is primarily used for diagnosing thermally intermittent problems with electronic devices, but it is also useful for protecting heat sensitive components during soldering, quickly cooling solder joints, and it can also be used to quickly remove gum and other adhesives from a variety of surfaces.
Product ID: 4331
MG Chemicals 832C Translucent Epoxy Encapsulating and Potting Compound is simple to mix, easy to use, provides great protection, and good value. It protects against static discharges, shocks, vibrations, and mechanical impacts. It insulates against heat and conductivity. It is extremely resistant to environmental humidity, salt water, and many harsh...
Product ID: 488
For removing exposed resist during the positive photofabrication process. Disolves exposed photoresist Concentrated formulation - dilute one part developer to ten parts water For best results, use in conjunction with M.G. Foam Brush (Cat. No. 416-S) Also available in the M.G. Photofabrication Kit (Cat. No. 416-K) .
Product ID: 491
A durable precision cleaning applicator, shred resistant made from 100% urethane foam head with 100PPI porosity. Bonded securely to a 6” birch shaft providing extra strength when additional pressure needs to be applied. Available in packs of 10, 50, 250 and 1000.